Sign up here and you can log into the forum!

WD TV LIVE power loss during update - BRICKED

Have a question about devices internals, memory layout, reverse engineering, etc---This is the place for anything so technical that it would cause a n00b's head to 'splode

WD TV LIVE power loss during update - BRICKED   

Postby toledi » Sat Feb 23, 2013 2:40 am

WD TV LIVE
WDBAAP0000NBK-00
DCM: NBAABA

during last official firmware update - powerloss (no electricity to whole house) - now WD is not working
power light is on, no picture (not on AV, not on HDMI)
on serial connect, putty list: (pressing 0,1,2 - nothing happened)

#xos2P4a-99 (sfla 128kbytes. subid 0xac/ac) [serial#70c67c13119af464408f9a49a0ab 8e70]
#stepxmb 0xac
#DRAM setup (method=0x10015858) ...
#DRAM0 Window : 0x#20#22#1e#20# (15)
#DRAM1 Window : 0x#22#23#20#22# (16)
#DRAM0 Settings: WD=0x0b0b0a0b RG=0x07080707 RR=0x07080707 RF=0x08080808
#DRAM1 Settings: WD=0x0a0d0a0a RG=0x08080708 RR=0x08080708 RF=0x09090909
#poisoned 131072 pages with 0xf6e686c3
#step6 @0x*** zxenv has been customized compared to build ***
--- review xmasboot/configs/922-A2.config for details [xmbb7-ezboot98-nand_st2] ---
xloadsize=59444
xload rc=6
subrom SHA-256: 43b5383fcd2ecd1f5366bea4eafc03bd740dc0a113af58d02846c117fb581b5b
ezboot98 @0xd00e5a94 (nand_st2) (actual cpu=@499MHz/dsp=333MHz/sys=333MHz)
on 8655 rev ES5 (subid 0xac) a2=0x00000002 a3=0x00000003
step12
#step22
ruamm0 [0x80000000,0x8f2f0000[ (~254738432 bytes)
ruamm1 [0xcca00000,0xcfd60000[ (~53870592 bytes)
[0xcfd20000,xos_public_ga=0xcfd20000[ and [0xcfd40000,0xcfd5ffff[ are lost for a lignment)
channel#ei
x_ga=0xcfd1fcd4
[0x8e800000,ios_ga=0x8e800000[ and [0x8eeacfc1,0x8f2f0000[ are lost for alignmen t)
GW32 0x0006f008 0xc0000000 [va=0x84000000]
GW32 0x0006f00c 0xc4000000 [va=0x88000000]
GW32 0x0006f010 0xc8000000 [va=0x8c000000]
step33
xos2k client version=19, server version=19
xos2 SHA-1 = ef2f712148b75194ab1d3c691b55bd4d3a5e956d (version 0x4a)
xos2 serial = 70c67c13119af464408f9a49a0ab8e70
Using zbootxenv ga=0xcfd0bcbc (va=0xbbd0bcbc)

**************************************
* SMP86xx zboot start ...
* Version: 3.1.0
* Started at 0xd00ed770.
* Configurations (chip revision: 1):
* Enabled checkpoints.
**************************************
DRAM0 dunit_cfg/delay0_ctrl (0x3514001a/0x4565132b).
DRAM1 dunit_cfg/delay0_ctrl (0x3514001a/0x4565132b).
Using UART port 0 as console.
Board ID.: villa_d2
Setting up H/W from XENV block at 0xbbd0bcbc.
Setting <SYSCLK avclk_mux> to 0x17400000.
Setting <SYSCLK hostclk_mux> to 0x00000130.
Setting <IRQ rise edge trigger lo> to 0xff28ca00.
Setting <IRQ fall edge trigger lo> to 0x0000c000.
Setting <IRQ rise edge trigger hi> to 0x0c10009f.
Setting <IRQ fall edge trigger hi> to 0x00000000.
Setting <IRQ GPIO map> to 0x000a0800.
Setting <PB default timing> to 0x03080202.
Keeping <PB timing0> to 0x03080202.
Keeping <PB Use timing0> to 0x000003f3.
Keeping <PB CS Config> to 0x00330003.
Enabled Devices: 0x001b3efc
PCIHost Ethernet Ethernet1 IR FIP I2CM I2CS USB PCIDev1 PCIDev2 PCIDev3 PCID ev4 SATA SCARD SCARD1
PCI IRQ routing:
IDSEL 1: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
IDSEL 2: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
IDSEL 3: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
IDSEL 4: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
Smartcard pin assignments:
OFF pin = 2
5V pin = 0
CMD pin = 1
Smartcard1 pin assignments:
OFF pin = 2
5V pin = 0
CMD pin = 1
cd#0 disabled
cd#1 disabled
cd#2 want 96000000Hz: setting of 0x0000000021c00000-2^28
cd#2 cannot measure
cd#3 disabled
cd#4 want 33333333Hz: setting of 0x0000000061333343-2^28
cd#4 measured to 33340kHz
cd#5 disabled
cd#6 disabled
cd#7 disabled
cd#8 disabled
cd#9 disabled
cd#10 disabled
cd#11 disabled
GPIO dir/data = 0x00000880/0x00000880
UART0 GPIO mode/dir/data = 0x6e/0x00/0x00
UART1 GPIO mode/dir/data = 0x6e/0x04/0x04
UART2 GPIO mode/dir/data = 0x00/0x00/0x00
Generate pulse(s) with GPIO7 .. 1,0(16us),1
MAC0: 00:90:a9:74:11:4e
MAC1: 00:16:e8:8f:9a:49
XENV block processing completed.
Default boot index: 2, sel:2
Boot Index (1)
xmboot booted from devtype: 0, chipsel: 0, phyblocknum: 0
Explicit boot order specified:
0x00 : devtype=0, CS=0
0x01 : devtype=0, CS=1
0x20 : devtype=2, CS=0
0x21 : devtype=2, CS=1
WARNING: ezboot encroaches upon ruamm#0 zone
ezboot buffers, setup in DRAM bank#0:
Alloting 1048576 bytes for heap.
Alloting 8388608 bytes for reading.
Alloting 8388608 bytes for decryption.
xmat romfs goes to 0xcfc0bca0 (ga)
xmat romfs goes to 0xb3c0bca0 (va)
Trying devtype=0 chipsel=0
nand_probe 0x0xd00f6ed0
nand_Mg_open 0
Reading NAND CS0, addr 0x016c0000, size 0x00000800 to 0xb3c0bca0
Not a valid ROMFS
Trying devtype=0 chipsel=1
nand_probe 0x0xd00f6ed0
Failed to init!
Failed to find valid xmat romfs in any device / chip select!
freeing xmat romfs buffer at 0xcfc0bca0
xmat romfs process failed.
Trying devtype=0 chipsel=0
reading z.boot1 (vzx=0xbbd0bcbc) is 0x000c0000
Reading NAND CS0, addr 0x000c0000, size 0x00000800 to 0x01740000
Not a valid ROMFS
reading z.boot2 (vzx=0xbbd0bcbc) is 0x003c0000
Reading NAND CS0, addr 0x003c0000, size 0x00000800 to 0x01740000
Not a valid ROMFS
Skipping boot container 3.
Skipping boot container 4.
Skipping boot container 5.
Skipping boot container 6.
Skipping boot container 7.
Trying devtype=0 chipsel=1
nand_probe 0x0xd00f6ed0
Failed to init!
Trying devtype=2 chipsel=0
toledi
n00b
 
Posts: 2
Joined: Sat Feb 23, 2013 2:34 am

Re: WD TV LIVE power loss during update - BRICKED   

Postby KAD » Sat Feb 23, 2013 8:45 am

you might want to read this

http://forum.wdlxtv.com/viewtopic.php?f=43&t=7798

your output says "not a valid ROMFS"

maybe loading over tftp would work
If you like my work please consider a Donation. Donate
Please read the appropriate documentation before posting questions! READ ME FAQ WIKI
PM's are for private matters. Post support questions to the appropriate forum, or they will be ignored.
User avatar
KAD
Global Moderator
 
Posts: 5103
Joined: Mon Apr 12, 2010 4:59 pm
Location: Seattle, WA USA

Re: WD TV LIVE power loss during update - BRICKED   

Postby toledi » Wed Feb 27, 2013 3:51 am

Can not get to Yamon.
Any body wants my WDTV Live - I give it away for free, you pay for P&P.
toledi
n00b
 
Posts: 2
Joined: Sat Feb 23, 2013 2:34 am

Re: WD TV LIVE power loss during update - BRICKED   

Postby recliq » Wed Feb 27, 2013 12:05 pm

Already got one like that, thanks :lol:
If you can't get into YAMON anymore it's really bricked. :(
­WDLXTV Project Maintainer
-:] If you like my contributions feel free to donate for a beer or a new flash drive. ...and always remember: RTFM! (README, FAQ, WIKI) [:-
User avatar
recliq
WDLXTV Team
 
Posts: 5513
Joined: Thu Apr 15, 2010 8:09 am
Location: Kiel, Germany

- BRICKED WDTV Live   

Postby funi » Tue Jun 17, 2014 1:46 am

Code: Select all
39idxfsef2f712148b75194ab1d3c691b55bd4d3a5e956dS

#xos2P4a-99 (sfla 128kbytes. subid 0xac/ac) [serial#52aa8ed10bc92da5e9e7de3cdeeabc9b]
#stepxmb 0xac
#DRAM setup (method=0x10015858) ...
#DRAM0 Window  :    0x#24#26#24#26# (18)
#DRAM1 Window  :    0x#2a#2c#26#28# (19)
#DRAM0 Settings: WD=0x0b0b0b0b RG=0x08090809 RR=0x08090809 RF=0x090a090a
#DRAM1 Settings: WD=0x0b0b0b0b RG=0x0a0a0909 RR=0x0a0a0909 RF=0x0a0b0a0a
#poisoned 131072 pages with 0x57f5ab35
#step6 @0*** zxenv has been customized compared to build ***
--- review xmasboot/configs/922-A2.config for details [xmbb7-ezboot98-nand_st2] ---
xloadsize=59444
xload rc=6
subrom SHA-256: 43b5383fcd2ecd1f5366bea4eafc03bd740dc0a113af58d02846c117fb581b5b
ezboot98 @0xd00e5a94 (nand_st2) (actual cpu=@499MHz/dsp=333MHz/sys=333MHz)
on 8655 rev ES5 (subid 0xac) a2=0x00000002 a3=0x00000003
step12
#step22
ruamm0 [0x80000000,0x8f2f0000[ (~254738432 bytes)
ruamm1 [0xcca00000,0xcfd60000[ (~53870592 bytes)
[0xcfd20000,xos_public_ga=0xcfd20000[ and [0xcfd40000,0xcfd5ffff[ are lost for alignment)
channel#ei
x_ga=0xcfd1fcd4
[0x8e800000,ios_ga=0x8e800000[ and [0x8eeacfc1,0x8f2f0000[ are lost for alignment)
GW32 0x0006f008 0xc0000000 [va=0x84000000]
GW32 0x0006f00c 0xc4000000 [va=0x88000000]
GW32 0x0006f010 0xc8000000 [va=0x8c000000]
step33
xos2k client version=19, server version=19
xos2 SHA-1 = ef2f712148b75194ab1d3c691b55bd4d3a5e956d (version 0x4a)
xos2 serial = 52aa8ed10bc92da5e9e7de3cdeeabc9b
Using zbootxenv ga=0xcfd0bcbc (va=0xbbd0bcbc)

**************************************
* SMP86xx zboot start ...
* Version: 3.1.0
* Started at 0xd00ed770.
* Configurations (chip revision: 1):
*    Enabled checkpoints.
**************************************
DRAM0 dunit_cfg/delay0_ctrl (0x3514001a/0x4565132b).
DRAM1 dunit_cfg/delay0_ctrl (0x3514001a/0x4565132b).
Using UART port 0 as console.
Board ID.: villa_d2
Setting up H/W from XENV block at 0xbbd0bcbc.
  Setting <SYSCLK avclk_mux> to 0x17400000.
  Setting <SYSCLK hostclk_mux> to 0x00000130.
  Setting <IRQ rise edge trigger lo> to 0xff28ca00.
  Setting <IRQ fall edge trigger lo> to 0x0000c000.
  Setting <IRQ rise edge trigger hi> to 0x0c10009f.
  Setting <IRQ fall edge trigger hi> to 0x00000000.
  Setting <IRQ GPIO map> to 0x000a0800.
  Setting <PB default timing> to 0x03080202.
  Keeping <PB timing0> to 0x03080202.
  Keeping <PB Use timing0> to 0x000003f3.
  Keeping <PB CS Config> to 0x00330003.
  Enabled Devices: 0x001b3efc
    PCIHost Ethernet Ethernet1 IR FIP I2CM I2CS USB PCIDev1 PCIDev2 PCIDev3 PCIDev4 SATA SCARD SCARD1
  PCI IRQ routing:
    IDSEL 1: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
    IDSEL 2: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
    IDSEL 3: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
    IDSEL 4: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
  Smartcard pin assignments:
    OFF pin = 2
    5V pin = 0
    CMD pin = 1
  Smartcard1 pin assignments:
    OFF pin = 2
    5V pin = 0
    CMD pin = 1
cd#0 disabled
cd#1 disabled
cd#2 want 96000000Hz: setting of 0x0000000021c00000-2^28
cd#2 cannot measure
cd#3 disabled
cd#4 want 33333333Hz: setting of 0x0000000061333343-2^28
cd#4 measured to 33340kHz
cd#5 disabled
cd#6 disabled
cd#7 disabled
cd#8 disabled
cd#9 disabled
cd#10 disabled
cd#11 disabled
  GPIO dir/data = 0x00000880/0x00000880
  UART0 GPIO mode/dir/data = 0x6e/0x00/0x00
  UART1 GPIO mode/dir/data = 0x6e/0x04/0x04
  UART2 GPIO mode/dir/data = 0x00/0x00/0x00
  Generate pulse(s) with GPIO7 .. 1,0(16us),1
  MAC0: 00:90:a9:74:96:6a
  MAC1: 00:16:e8:e7:de:3c
XENV block processing completed.
Default boot index: 1, sel:1
Boot Index (0)
xmboot booted from devtype: 0, chipsel: 0, phyblocknum: 0
Explicit boot order specified:
  0x00 : devtype=0, CS=0
  0x01 : devtype=0, CS=1
  0x20 : devtype=2, CS=0
  0x21 : devtype=2, CS=1
WARNING: ezboot encroaches upon ruamm#0 zone
ezboot buffers, setup in DRAM bank#0:
  Alloting 1048576 bytes for heap.
  Alloting 8388608 bytes for reading.
  Alloting 8388608 bytes for decryption.
xmat romfs goes to 0xcfc0bca0 (ga)
xmat romfs goes to 0xb3c0bca0 (va)
Trying devtype=0 chipsel=0
nand_probe 0x0xd00f6ed0
nand_Mg_open 0
Reading NAND CS0, addr 0x016c0000, size 0x00000800 to 0xb3c0bca0
Not a valid ROMFS
Trying devtype=0 chipsel=1
nand_probe 0x0xd00f6ed0
Failed to init!
Failed to find valid xmat romfs in any device / chip select!
freeing xmat romfs buffer at 0xcfc0bca0
xmat romfs process failed.
Trying devtype=0 chipsel=0
reading z.boot0 (vzx=0xbbd0bcbc) is 0x00080000
Reading NAND CS0, addr 0x00080000, size 0x00000800 to 0x01740000
Not a valid ROMFS
reading z.boot1 (vzx=0xbbd0bcbc) is 0x000c0000
Reading NAND CS0, addr 0x000c0000, size 0x00000800 to 0x01740000
Not a valid ROMFS
reading z.boot2 (vzx=0xbbd0bcbc) is 0x003c0000
Reading NAND CS0, addr 0x003c0000, size 0x00000800 to 0x01740000
Not a valid ROMFS
Skipping boot container 3.
Skipping boot container 4.
Skipping boot container 5.
Skipping boot container 6.
Skipping boot container 7.
Trying devtype=0 chipsel=1
nand_probe 0x0xd00f6ed0
Failed to init!
Trying devtype=2 chipsel=0
39idxfsef2f712148b75194ab1d3c691b55bd4d3a5e956dS

#xos2P4a-99 (sfla 128kbytes. subid 0xac/ac) [serial#52aa8ed10bc92da5e9e7de3cdeeabc9b]
#stepxmb 0xac
#DRAM setup (method=0x10015858) ...
#DRAM0 Window  :    0x#24#26#24#26# (18)
#DRAM1 Window  :    0x#2a#2c#26#28# (19)
#DRAM0 Settings: WD=0x0b0b0b0b RG=0x08090809 RR=0x08090809 RF=0x090a090a
#DRAM1 Settings: WD=0x0b0b0b0b RG=0x0a0a0909 RR=0x0a0a0909 RF=0x0a0b0a0a
#poisoned 131072 pages with 0x546145b8
#step6 @*** zxenv has been customized compared to build ***
--- review xmasboot/configs/922-A2.config for details [xmbb7-ezboot98-nand_st2] ---
xloadsize=59444
xload rc=6
subrom SHA-256: 43b5383fcd2ecd1f5366bea4eafc03bd740dc0a113af58d02846c117fb581b5b
ezboot98 @0xd00e5a94 (nand_st2) (actual cpu=@499MHz/dsp=333MHz/sys=333MHz)
on 8655 rev ES5 (subid 0xac) a2=0x00000002 a3=0x00000003
step12
#step22
ruamm0 [0x80000000,0x8f2f0000[ (~254738432 bytes)
ruamm1 [0xcca00000,0xcfd60000[ (~53870592 bytes)
[0xcfd20000,xos_public_ga=0xcfd20000[ and [0xcfd40000,0xcfd5ffff[ are lost for alignment)
ex_ga=0xcfd1fcd4
[0x8e800000,ios_ga=0x8e800000[ and [0x8eeacfc1,0x8f2f0000[ are lost for alignment)
GW32 0x0006f008 0xc0000000 [va=0x84000000]
GW32 0x0006f00c 0xc4000000 [va=0x88000000]
GW32 0x0006f010 0xc8000000 [va=0x8c000000]
step33
xos2k client version=19, server version=19
xos2 SHA-1 = ef2f712148b75194ab1d3c691b55bd4d3a5e956d (version 0x4a)
xos2 serial = 52aa8ed10bc92da5e9e7de3cdeeabc9b
Using zbootxenv ga=0xcfd0bcbc (va=0xbbd0bcbc)

**************************************
* SMP86xx zboot start ...
* Version: 3.1.0
* Started at 0xd00ed770.
* Configurations (chip revision: 1):
*    Enabled checkpoints.
**************************************
DRAM0 dunit_cfg/delay0_ctrl (0x3514001a/0x4565132b).
DRAM1 dunit_cfg/delay0_ctrl (0x3514001a/0x4565132b).
Using UART port 0 as console.
Board ID.: villa_d2
Setting up H/W from XENV block at 0xbbd0bcbc.
  Setting <SYSCLK avclk_mux> to 0x17400000.
  Setting <SYSCLK hostclk_mux> to 0x00000130.
  Setting <IRQ rise edge trigger lo> to 0xff28ca00.
  Setting <IRQ fall edge trigger lo> to 0x0000c000.
  Setting <IRQ rise edge trigger hi> to 0x0c10009f.
  Setting <IRQ fall edge trigger hi> to 0x00000000.
  Setting <IRQ GPIO map> to 0x000a0800.
  Setting <PB default timing> to 0x03080202.
  Keeping <PB timing0> to 0x03080202.
  Keeping <PB Use timing0> to 0x000003f3.
  Keeping <PB CS Config> to 0x00330003.
  Enabled Devices: 0x001b3efc
    PCIHost Ethernet Ethernet1 IR FIP I2CM I2CS USB PCIDev1 PCIDev2 PCIDev3 PCIDev4 SATA SCARD SCARD1
  PCI IRQ routing:
    IDSEL 1: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
    IDSEL 2: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
    IDSEL 3: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
    IDSEL 4: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
  Smartcard pin assignments:
    OFF pin = 2
    5V pin = 0
    CMD pin = 1
  Smartcard1 pin assignments:
    OFF pin = 2
    5V pin = 0
    CMD pin = 1
cd#0 disabled
cd#1 disabled
cd#2 want 96000000Hz: setting of 0x0000000021c00000-2^28
cd#2 cannot measure
cd#3 disabled
cd#4 want 33333333Hz: setting of 0x0000000061333343-2^28
cd#4 measured to 33336kHz
cd#5 disabled
cd#6 disabled
cd#7 disabled
cd#8 disabled
cd#9 disabled
cd#10 disabled
cd#11 disabled
  GPIO dir/data = 0x00000880/0x00000880
  UART0 GPIO mode/dir/data = 0x6e/0x00/0x00
  UART1 GPIO mode/dir/data = 0x6e/0x04/0x04
  UART2 GPIO mode/dir/data = 0x00/0x00/0x00
  Generate pulse(s) with GPIO7 .. 1,0(16us),1
  MAC0: 00:90:a9:74:96:6a
  MAC1: 00:16:e8:e7:de:3c
XENV block processing completed.
Default boot index: 1, sel:1
Boot Index (2)
xmboot booted from devtype: 0, chipsel: 0, phyblocknum: 0
Explicit boot order specified:
  0x00 : devtype=0, CS=0
  0x01 : devtype=0, CS=1
  0x20 : devtype=2, CS=0
  0x21 : devtype=2, CS=1
WARNING: ezboot encroaches upon ruamm#0 zone
ezboot buffers, setup in DRAM bank#0:
  Alloting 1048576 bytes for heap.
  Alloting 8388608 bytes for reading.
  Alloting 8388608 bytes for decryption.
xmat romfs goes to 0xcfc0bca0 (ga)
xmat romfs goes to 0xb3c0bca0 (va)
Trying devtype=0 chipsel=0
nand_probe 0x0xd00f6ed0
nand_Mg_open 0
Reading NAND CS0, addr 0x016c0000, size 0x00000800 to 0xb3c0bca0
Not a valid ROMFS
Trying devtype=0 chipsel=1
nand_probe 0x0xd00f6ed0
Failed to init!
Failed to find valid xmat romfs in any device / chip select!
freeing xmat romfs buffer at 0xcfc0bca0
xmat romfs process failed.
Trying devtype=0 chipsel=0
reading z.boot2 (vzx=0xbbd0bcbc) is 0x003c0000
Reading NAND CS0, addr 0x003c0000, size 0x00000800 to 0x01740000
Not a valid ROMFS
Skipping boot container 3.
Skipping boot container 4.
Skipping boot container 5.
Skipping boot container 6.
Skipping boot container 7.
Trying devtype=0 chipsel=1
nand_probe 0x0xd00f6ed0
Failed to init!
Trying devtype=2 chipsel=0
39idxfsef2f712148b75194ab1d3c691b55bd4d3a5e956dS

#xos2P4a-99 (sfla 128kbytes. subid 0xac/ac) [serial#52aa8ed10bc92da5e9e7de3cdeeabc9b]
#stepxmb 0xac
#DRAM setup (method=0x10015858) ...
#DRAM0 Window  :    0x#24#26#24#26# (18)
#DRAM1 Window  :    0x#2a#2c#26#28# (19)
#DRAM0 Settings: WD=0x0b0b0b0b RG=0x08090809 RR=0x08090809 RF=0x090a090a
#DRAM1 Settings: WD=0x0b0b0b0b RG=0x0a0a0909 RR=0x0a0a0909 RF=0x0a0b0a0a
#poisoned 131072 pages with 0xa7f2ce16
#step6 @0*** zxenv has been customized compared to build ***
--- review xmasboot/configs/922-A2.config for details [xmbb7-ezboot98-nand_st2] ---
xloadsize=59444
xload rc=6
subrom SHA-256: 43b5383fcd2ecd1f5366bea4eafc03bd740dc0a113af58d02846c117fb581b5b
ezboot98 @0xd00e5a94 (nand_st2) (actual cpu=@499MHz/dsp=333MHz/sys=333MHz)
on 8655 rev ES5 (subid 0xac) a2=0x00000002 a3=0x00000003
step12
#step22
ruamm0 [0x80000000,0x8f2f0000[ (~254738432 bytes)
ruamm1 [0xcca00000,0xcfd60000[ (~53870592 bytes)
[0xcfd20000,xos_public_ga=0xcfd20000[ and [0xcfd40000,0xcfd5ffff[ are lost for alignment)
x_ga=0xcfd1fcd4
[0x8e800000,ios_ga=0x8e800000[ and [0x8eeacfc1,0x8f2f0000[ are lost for alignment)
GW32 0x0006f008 0xc0000000 [va=0x84000000]
GW32 0x0006f00c 0xc4000000 [va=0x88000000]
GW32 0x0006f010 0xc8000000 [va=0x8c000000]
step33
xos2k client version=19, server version=19
xos2 SHA-1 = ef2f712148b75194ab1d3c691b55bd4d3a5e956d (version 0x4a)
xos2 serial = 52aa8ed10bc92da5e9e7de3cdeeabc9b
Using zbootxenv ga=0xcfd0bcbc (va=0xbbd0bcbc)

**************************************
* SMP86xx zboot start ...
* Version: 3.1.0
* Started at 0xd00ed770.
* Configurations (chip revision: 1):
*    Enabled checkpoints.
**************************************
DRAM0 dunit_cfg/delay0_ctrl (0x3514001a/0x4565132b).
DRAM1 dunit_cfg/delay0_ctrl (0x3514001a/0x4565132b).
Using UART port 0 as console.
Board ID.: villa_d2
Setting up H/W from XENV block at 0xbbd0bcbc.
  Setting <SYSCLK avclk_mux> to 0x17400000.
  Setting <SYSCLK hostclk_mux> to 0x00000130.
  Setting <IRQ rise edge trigger lo> to 0xff28ca00.
  Setting <IRQ fall edge trigger lo> to 0x0000c000.
  Setting <IRQ rise edge trigger hi> to 0x0c10009f.
  Setting <IRQ fall edge trigger hi> to 0x00000000.
  Setting <IRQ GPIO map> to 0x000a0800.
  Setting <PB default timing> to 0x03080202.
  Keeping <PB timing0> to 0x03080202.
  Keeping <PB Use timing0> to 0x000003f3.
  Keeping <PB CS Config> to 0x00330003.
  Enabled Devices: 0x001b3efc
    PCIHost Ethernet Ethernet1 IR FIP I2CM I2CS USB PCIDev1 PCIDev2 PCIDev3 PCIDev4 SATA SCARD SCARD1
  PCI IRQ routing:
    IDSEL 1: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
    IDSEL 2: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
    IDSEL 3: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
    IDSEL 4: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
  Smartcard pin assignments:
    OFF pin = 2
    5V pin = 0
    CMD pin = 1
  Smartcard1 pin assignments:
    OFF pin = 2
    5V pin = 0
    CMD pin = 1
cd#0 disabled
cd#1 disabled
cd#2 want 96000000Hz: setting of 0x0000000021c00000-2^28
cd#2 cannot measure
cd#3 disabled
cd#4 want 33333333Hz: setting of 0x0000000061333343-2^28
cd#4 measured to 33336kHz
cd#5 disabled
cd#6 disabled
cd#7 disabled
cd#8 disabled
cd#9 disabled
cd#10 disabled
cd#11 disabled
  GPIO dir/data = 0x00000880/0x00000880
  UART0 GPIO mode/dir/data = 0x6e/0x00/0x00
  UART1 GPIO mode/dir/data = 0x6e/0x04/0x04
  UART2 GPIO mode/dir/data = 0x00/0x00/0x00
  Generate pulse(s) with GPIO7 .. 1,0(16us),1
  MAC0: 00:90:a9:74:96:6a
  MAC1: 00:16:e8:e7:de:3c
XENV block processing completed.
Default boot index: 1, sel:1
Boot Index (2)
xmboot booted from devtype: 0, chipsel: 0, phyblocknum: 0
Explicit boot order specified:
  0x00 : devtype=0, CS=0
  0x01 : devtype=0, CS=1
  0x20 : devtype=2, CS=0
  0x21 : devtype=2, CS=1
WARNING: ezboot encroaches upon ruamm#0 zone
ezboot buffers, setup in DRAM bank#0:
  Alloting 1048576 bytes for heap.
  Alloting 8388608 bytes for reading.
  Alloting 8388608 bytes for decryption.
xmat romfs goes to 0xcfc0bca0 (ga)
xmat romfs goes to 0xb3c0bca0 (va)
Trying devtype=0 chipsel=0
nand_probe 0x0xd00f6ed0
nand_Mg_open 0
Reading NAND CS0, addr 0x016c0000, size 0x00000800 to 0xb3c0bca0
Not a valid ROMFS
Trying devtype=0 chipsel=1
nand_probe 0x0xd00f6ed0
Failed to init!
Failed to find valid xmat romfs in any device / chip select!
freeing xmat romfs buffer at 0xcfc0bca0
xmat romfs process failed.
Trying devtype=0 chipsel=0
reading z.boot2 (vzx=0xbbd0bcbc) is 0x003c0000
Reading NAND CS0, addr 0x003c0000, size 0x00000800 to 0x01740000
Not a valid ROMFS
Skipping boot container 3.
Skipping boot container 4.
Skipping boot container 5.
Skipping boot container 6.
Skipping boot container 7.
Trying devtype=0 chipsel=1
nand_probe 0x0xd00f6ed0
Failed to init!
Trying devtype=2 chipsel=0
39idxfsef2f712148b75194ab1d3c691b55bd4d3a5e956dS

#xos2P4a-99 (sfla 128kbytes. subid 0xac/ac) [serial#52aa8ed10bc92da5e9e7de3cdeeabc9b]
#stepxm
       b 0xac
#DRAM setup (method=0x10015858) ...
#DRAM0 Window  :    0x#24#26#24#26# (18)
#DRAM1 Window  :    0x#2a#2c#26#28# (19)
#DRAM0 Settings: WD=0x0b0b0b0b RG=0x08090809 RR=0x08090809 RF=0x090a090a
#DRAM1 Settings: WD=0x0b0b0b0b RG=0x0a0a0909 RR=0x0a0a0909 RF=0x0a0b0a0a
#poisoned 131072 pages with 0x0d75f738
#step6 @0*** zxenv has been customized compared to build ***
--- review xmasboot/configs/922-A2.config for details [xmbb7-ezboot98-nand_st2] ---
xloadsize=59444
xload rc=6
subrom SHA-256: 43b5383fcd2ecd1f5366bea4eafc03bd740dc0a113af58d02846c117fb581b5b
ezboot98 @0xd00e5a94 (nand_st2) (actual cpu=@499MHz/dsp=333MHz/sys=333MHz)
on 8655 rev ES5 (subid 0xac) a2=0x00000002 a3=0x00000003
step12
#step22
ruamm0 [0x80000000,0x8f2f0000[ (~254738432 bytes)
ruamm1 [0xcca00000,0xcfd60000[ (~53870592 bytes)
[0xcfd20000,xos_public_ga=0xcfd20000[ and [0xcfd40000,0xcfd5ffff[ are lost for alignment)
channel#ei
x_ga=0xcfd1fcd4
[0x8e800000,ios_ga=0x8e800000[ and [0x8eeacfc1,0x8f2f0000[ are lost for alignment)
GW32 0x0006f008 0xc0000000 [va=0x84000000]
GW32 0x0006f00c 0xc4000000 [va=0x88000000]
GW32 0x0006f010 0xc8000000 [va=0x8c000000]
step33
xos2k client version=19, server version=19
xos2 SHA-1 = ef2f712148b75194ab1d3c691b55bd4d3a5e956d (version 0x4a)
xos2 serial = 52aa8ed10bc92da5e9e7de3cdeeabc9b
Using zbootxenv ga=0xcfd0bcbc (va=0xbbd0bcbc)

**************************************
* SMP86xx zboot start ...
* Version: 3.1.0
* Started at 0xd00ed770.
* Configurations (chip revision: 1):
*    Enabled checkpoints.
**************************************
DRAM0 dunit_cfg/delay0_ctrl (0x3514001a/0x4565132b).
DRAM1 dunit_cfg/delay0_ctrl (0x3514001a/0x4565132b).
Using UART port 0 as console.
Board ID.: villa_d2
Setting up H/W from XENV block at 0xbbd0bcbc.
  Setting <SYSCLK avclk_mux> to 0x17400000.
  Setting <SYSCLK hostclk_mux> to 0x00000130.
  Setting <IRQ rise edge trigger lo> to 0xff28ca00.
  Setting <IRQ fall edge trigger lo> to 0x0000c000.
  Setting <IRQ rise edge trigger hi> to 0x0c10009f.
  Setting <IRQ fall edge trigger hi> to 0x00000000.
  Setting <IRQ GPIO map> to 0x000a0800.
  Setting <PB default timing> to 0x03080202.
  Keeping <PB timing0> to 0x03080202.
  Keeping <PB Use timing0> to 0x000003f3.
  Keeping <PB CS Config> to 0x00330003.
  Enabled Devices: 0x001b3efc
    PCIHost Ethernet Ethernet1 IR FIP I2CM I2CS USB PCIDev1 PCIDev2 PCIDev3 PCIDev4 SATA SCARD SCARD1
  PCI IRQ routing:
    IDSEL 1: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
    IDSEL 2: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
    IDSEL 3: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
    IDSEL 4: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
  Smartcard pin assignments:
    OFF pin = 2
    5V pin = 0
    CMD pin = 1
  Smartcard1 pin assignments:
    OFF pin = 2
    5V pin = 0
    CMD pin = 1
cd#0 disabled
cd#1 disabled
cd#2 want 96000000Hz: setting of 0x0000000021c00000-2^28
cd#2 cannot measure
cd#3 disabled
cd#4 want 33333333Hz: setting of 0x0000000061333343-2^28
cd#4 measured to 33344kHz
cd#5 disabled
cd#6 disabled
cd#7 disabled
cd#8 disabled
cd#9 disabled
cd#10 disabled
cd#11 disabled
  GPIO dir/data = 0x00000880/0x00000880
  UART0 GPIO mode/dir/data = 0x6e/0x00/0x00
  UART1 GPIO mode/dir/data = 0x6e/0x04/0x04
  UART2 GPIO mode/dir/data = 0x00/0x00/0x00
  Generate pulse(s) with GPIO7 .. 1,0(16us),1
  MAC0: 00:90:a9:74:96:6a
  MAC1: 00:16:e8:e7:de:3c
XENV block processing completed.
Default boot index: 1, sel:1
Boot Index (0)
xmboot booted from devtype: 0, chipsel: 0, phyblocknum: 0
Explicit boot order specified:
  0x00 : devtype=0, CS=0
  0x01 : devtype=0, CS=1
  0x20 : devtype=2, CS=0
  0x21 : devtype=2, CS=1
WARNING: ezboot encroaches upon ruamm#0 zone
ezboot buffers, setup in DRAM bank#0:
  Alloting 1048576 bytes for heap.
  Alloting 8388608 bytes for reading.
  Alloting 8388608 bytes for decryption.
xmat romfs goes to 0xcfc0bca0 (ga)
xmat romfs goes to 0xb3c0bca0 (va)
Trying devtype=0 chipsel=0
nand_probe 0x0xd00f6ed0
nand_Mg_open 0
Reading NAND CS0, addr 0x016c0000, size 0x00000800 to 0xb3c0bca0
Not a valid ROMFS
Trying devtype=0 chipsel=1
nand_probe 0x0xd00f6ed0
Failed to init!
Failed to find valid xmat romfs in any device / chip select!
freeing xmat romfs buffer at 0xcfc0bca0
xmat romfs process failed.
Trying devtype=0 chipsel=0
reading z.boot0 (vzx=0xbbd0bcbc) is 0x00080000
Reading NAND CS0, addr 0x00080000, size 0x00000800 to 0x01740000
Not a valid ROMFS
reading z.boot1 (vzx=0xbbd0bcbc) is 0x000c0000
Reading NAND CS0, addr 0x000c0000, size 0x00000800 to 0x01740000
Not a valid ROMFS
reading z.boot2 (vzx=0xbbd0bcbc) is 0x003c0000
Reading NAND CS0, addr 0x003c0000, size 0x00000800 to 0x01740000
Not a valid ROMFS
Skipping boot container 3.
Skipping boot container 4.
Skipping boot container 5.
Skipping boot container 6.
Skipping boot container 7.
Trying devtype=0 chipsel=1
nand_probe 0x0xd00f6ed0
Failed to init!
Trying devtype=2 chipsel=0
funi
n00b
 
Posts: 3
Joined: Fri Jun 06, 2014 9:51 am

Re: - BRICKED WDTV Live   

Postby funi » Tue Jun 17, 2014 1:51 am

Code: Select all
39idxfsef2f712148b75194ab1d3c691b55bd4d3a5e956dS

#xos2P4a-99 (sfla 128kbytes. subid 0xac/ac) [serial#52aa8ed10bc92da5e9e7de3cdeeabc9b]
#stepxmb 0xac
#DRAM setup (method=0x10015858) ...
#DRAM0 Window  :    0x#24#26#24#26# (18)
#DRAM1 Window  :    0x#2a#2c#26#28# (19)
#DRAM0 Settings: WD=0x0b0b0b0b RG=0x08090809 RR=0x08090809 RF=0x090a090a
#DRAM1 Settings: WD=0x0b0b0b0b RG=0x0a0a0909 RR=0x0a0a0909 RF=0x0a0b0a0a
#poisoned 131072 pages with 0x57f5ab35
#step6 @0*** zxenv has been customized compared to build ***
--- review xmasboot/configs/922-A2.config for details [xmbb7-ezboot98-nand_st2] ---
xloadsize=59444
xload rc=6

subrom SHA-256: 43b5383fcd2ecd1f5366bea4eafc03bd740dc0a113af58d02846c117fb581b5b
ezboot98 @0xd00e5a94 (nand_st2) (actual cpu=@499MHz/dsp=333MHz/sys=333MHz)
on 8655 rev ES5 (subid 0xac) a2=0x00000002 a3=0x00000003
step12
#step22
ruamm0 [0x80000000,0x8f2f0000[ (~254738432 bytes)
ruamm1 [0xcca00000,0xcfd60000[ (~53870592 bytes)
[0xcfd20000,xos_public_ga=0xcfd20000[ and [0xcfd40000,0xcfd5ffff[ are lost for alignment)
channel#ei
x_ga=0xcfd1fcd4
[0x8e800000,ios_ga=0x8e800000[ and [0x8eeacfc1,0x8f2f0000[ are lost for alignment)
GW32 0x0006f008 0xc0000000 [va=0x84000000]
GW32 0x0006f00c 0xc4000000 [va=0x88000000]
GW32 0x0006f010 0xc8000000 [va=0x8c000000]
step33
xos2k client version=19, server version=19
xos2 SHA-1 = ef2f712148b75194ab1d3c691b55bd4d3a5e956d (version 0x4a)
xos2 serial = 52aa8ed10bc92da5e9e7de3cdeeabc9b
Using zbootxenv ga=0xcfd0bcbc (va=0xbbd0bcbc)

**************************************
* SMP86xx zboot start ...
* Version: 3.1.0
* Started at 0xd00ed770.
* Configurations (chip revision: 1):
*    Enabled checkpoints.
**************************************
DRAM0 dunit_cfg/delay0_ctrl (0x3514001a/0x4565132b).
DRAM1 dunit_cfg/delay0_ctrl (0x3514001a/0x4565132b).
Using UART port 0 as console.
Board ID.: villa_d2
Setting up H/W from XENV block at 0xbbd0bcbc.
  Setting <SYSCLK avclk_mux> to 0x17400000.
  Setting <SYSCLK hostclk_mux> to 0x00000130.
  Setting <IRQ rise edge trigger lo> to 0xff28ca00.
  Setting <IRQ fall edge trigger lo> to 0x0000c000.
  Setting <IRQ rise edge trigger hi> to 0x0c10009f.
  Setting <IRQ fall edge trigger hi> to 0x00000000.
  Setting <IRQ GPIO map> to 0x000a0800.
  Setting <PB default timing> to 0x03080202.
  Keeping <PB timing0> to 0x03080202.
  Keeping <PB Use timing0> to 0x000003f3.
  Keeping <PB CS Config> to 0x00330003.
  Enabled Devices: 0x001b3efc
    PCIHost Ethernet Ethernet1 IR FIP I2CM I2CS USB PCIDev1 PCIDev2 PCIDev3 PCIDev4 SATA SCARD SCARD1
  PCI IRQ routing:
    IDSEL 1: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
    IDSEL 2: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
    IDSEL 3: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
    IDSEL 4: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
  Smartcard pin assignments:
    OFF pin = 2
    5V pin = 0
    CMD pin = 1
  Smartcard1 pin assignments:
    OFF pin = 2
    5V pin = 0
    CMD pin = 1
cd#0 disabled
cd#1 disabled
cd#2 want 96000000Hz: setting of 0x0000000021c00000-2^28
cd#2 cannot measure
cd#3 disabled
cd#4 want 33333333Hz: setting of 0x0000000061333343-2^28
cd#4 measured to 33340kHz
cd#5 disabled
cd#6 disabled
cd#7 disabled
cd#8 disabled
cd#9 disabled
cd#10 disabled
cd#11 disabled
  GPIO dir/data = 0x00000880/0x00000880
  UART0 GPIO mode/dir/data = 0x6e/0x00/0x00
  UART1 GPIO mode/dir/data = 0x6e/0x04/0x04
  UART2 GPIO mode/dir/data = 0x00/0x00/0x00
  Generate pulse(s) with GPIO7 .. 1,0(16us),1
  MAC0: 00:90:a9:74:96:6a
  MAC1: 00:16:e8:e7:de:3c
XENV block processing completed.
Default boot index: 1, sel:1
Boot Index (0)
xmboot booted from devtype: 0, chipsel: 0, phyblocknum: 0
Explicit boot order specified:
  0x00 : devtype=0, CS=0
  0x01 : devtype=0, CS=1
  0x20 : devtype=2, CS=0
  0x21 : devtype=2, CS=1
WARNING: ezboot encroaches upon ruamm#0 zone
ezboot buffers, setup in DRAM bank#0:
  Alloting 1048576 bytes for heap.
  Alloting 8388608 bytes for reading.
  Alloting 8388608 bytes for decryption.
xmat romfs goes to 0xcfc0bca0 (ga)
xmat romfs goes to 0xb3c0bca0 (va)
Trying devtype=0 chipsel=0
nand_probe 0x0xd00f6ed0
nand_Mg_open 0
Reading NAND CS0, addr 0x016c0000, size 0x00000800 to 0xb3c0bca0
Not a valid ROMFS
Trying devtype=0 chipsel=1
nand_probe 0x0xd00f6ed0
Failed to init!
Failed to find valid xmat romfs in any device / chip select!
freeing xmat romfs buffer at 0xcfc0bca0
xmat romfs process failed.
Trying devtype=0 chipsel=0
reading z.boot0 (vzx=0xbbd0bcbc) is 0x00080000
Reading NAND CS0, addr 0x00080000, size 0x00000800 to 0x01740000
Not a valid ROMFS
reading z.boot1 (vzx=0xbbd0bcbc) is 0x000c0000
Reading NAND CS0, addr 0x000c0000, size 0x00000800 to 0x01740000
Not a valid ROMFS
reading z.boot2 (vzx=0xbbd0bcbc) is 0x003c0000
Reading NAND CS0, addr 0x003c0000, size 0x00000800 to 0x01740000
Not a valid ROMFS
Skipping boot container 3.
Skipping boot container 4.
Skipping boot container 5.
Skipping boot container 6.
Skipping boot container 7.
Trying devtype=0 chipsel=1
nand_probe 0x0xd00f6ed0
Failed to init!
Trying devtype=2 chipsel=0
39idxfsef2f712148b75194ab1d3c691b55bd4d3a5e956dS

#xos2P4a-99 (sfla 128kbytes. subid 0xac/ac) [serial#52aa8ed10bc92da5e9e7de3cdeeabc9b]
#stepxmb 0xac
#DRAM setup (method=0x10015858) ...
#DRAM0 Window  :    0x#24#26#24#26# (18)
#DRAM1 Window  :    0x#2a#2c#26#28# (19)
#DRAM0 Settings: WD=0x0b0b0b0b RG=0x08090809 RR=0x08090809 RF=0x090a090a
#DRAM1 Settings: WD=0x0b0b0b0b RG=0x0a0a0909 RR=0x0a0a0909 RF=0x0a0b0a0a
#poisoned 131072 pages with 0x546145b8
#step6 @*** zxenv has been customized compared to build ***
--- review xmasboot/configs/922-A2.config for details [xmbb7-ezboot98-nand_st2] ---
xloadsize=59444
xload rc=6
subrom SHA-256: 43b5383fcd2ecd1f5366bea4eafc03bd740dc0a113af58d02846c117fb581b5b
ezboot98 @0xd00e5a94 (nand_st2) (actual cpu=@499MHz/dsp=333MHz/sys=333MHz)
on 8655 rev ES5 (subid 0xac) a2=0x00000002 a3=0x00000003
step12
#step22
ruamm0 [0x80000000,0x8f2f0000[ (~254738432 bytes)
ruamm1 [0xcca00000,0xcfd60000[ (~53870592 bytes)
[0xcfd20000,xos_public_ga=0xcfd20000[ and [0xcfd40000,0xcfd5ffff[ are lost for alignment)
ex_ga=0xcfd1fcd4
[0x8e800000,ios_ga=0x8e800000[ and [0x8eeacfc1,0x8f2f0000[ are lost for alignment)
GW32 0x0006f008 0xc0000000 [va=0x84000000]
GW32 0x0006f00c 0xc4000000 [va=0x88000000]
GW32 0x0006f010 0xc8000000 [va=0x8c000000]
step33
xos2k client version=19, server version=19
xos2 SHA-1 = ef2f712148b75194ab1d3c691b55bd4d3a5e956d (version 0x4a)
xos2 serial = 52aa8ed10bc92da5e9e7de3cdeeabc9b
Using zbootxenv ga=0xcfd0bcbc (va=0xbbd0bcbc)

**************************************
* SMP86xx zboot start ...
* Version: 3.1.0
* Started at 0xd00ed770.
* Configurations (chip revision: 1):
*    Enabled checkpoints.
**************************************
DRAM0 dunit_cfg/delay0_ctrl (0x3514001a/0x4565132b).
DRAM1 dunit_cfg/delay0_ctrl (0x3514001a/0x4565132b).
Using UART port 0 as console.
Board ID.: villa_d2
Setting up H/W from XENV block at 0xbbd0bcbc.
  Setting <SYSCLK avclk_mux> to 0x17400000.
  Setting <SYSCLK hostclk_mux> to 0x00000130.
  Setting <IRQ rise edge trigger lo> to 0xff28ca00.
  Setting <IRQ fall edge trigger lo> to 0x0000c000.
  Setting <IRQ rise edge trigger hi> to 0x0c10009f.
  Setting <IRQ fall edge trigger hi> to 0x00000000.
  Setting <IRQ GPIO map> to 0x000a0800.
  Setting <PB default timing> to 0x03080202.
  Keeping <PB timing0> to 0x03080202.
  Keeping <PB Use timing0> to 0x000003f3.
  Keeping <PB CS Config> to 0x00330003.
  Enabled Devices: 0x001b3efc
    PCIHost Ethernet Ethernet1 IR FIP I2CM I2CS USB PCIDev1 PCIDev2 PCIDev3 PCIDev4 SATA SCARD SCARD1
  PCI IRQ routing:
    IDSEL 1: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
    IDSEL 2: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
    IDSEL 3: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
    IDSEL 4: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
  Smartcard pin assignments:
    OFF pin = 2
    5V pin = 0
    CMD pin = 1
  Smartcard1 pin assignments:
    OFF pin = 2
    5V pin = 0
    CMD pin = 1
cd#0 disabled
cd#1 disabled
cd#2 want 96000000Hz: setting of 0x0000000021c00000-2^28
cd#2 cannot measure
cd#3 disabled
cd#4 want 33333333Hz: setting of 0x0000000061333343-2^28
cd#4 measured to 33336kHz
cd#5 disabled
cd#6 disabled
cd#7 disabled
cd#8 disabled
cd#9 disabled
cd#10 disabled
cd#11 disabled
  GPIO dir/data = 0x00000880/0x00000880
  UART0 GPIO mode/dir/data = 0x6e/0x00/0x00
  UART1 GPIO mode/dir/data = 0x6e/0x04/0x04
  UART2 GPIO mode/dir/data = 0x00/0x00/0x00
  Generate pulse(s) with GPIO7 .. 1,0(16us),1
  MAC0: 00:90:a9:74:96:6a
  MAC1: 00:16:e8:e7:de:3c
XENV block processing completed.
Default boot index: 1, sel:1
Boot Index (2)
xmboot booted from devtype: 0, chipsel: 0, phyblocknum: 0
Explicit boot order specified:
  0x00 : devtype=0, CS=0
  0x01 : devtype=0, CS=1
  0x20 : devtype=2, CS=0
  0x21 : devtype=2, CS=1
WARNING: ezboot encroaches upon ruamm#0 zone
ezboot buffers, setup in DRAM bank#0:
  Alloting 1048576 bytes for heap.
  Alloting 8388608 bytes for reading.
  Alloting 8388608 bytes for decryption.
xmat romfs goes to 0xcfc0bca0 (ga)
xmat romfs goes to 0xb3c0bca0 (va)
Trying devtype=0 chipsel=0
nand_probe 0x0xd00f6ed0
nand_Mg_open 0
Reading NAND CS0, addr 0x016c0000, size 0x00000800 to 0xb3c0bca0
Not a valid ROMFS
Trying devtype=0 chipsel=1
nand_probe 0x0xd00f6ed0
Failed to init!
Failed to find valid xmat romfs in any device / chip select!
freeing xmat romfs buffer at 0xcfc0bca0
xmat romfs process failed.
Trying devtype=0 chipsel=0
reading z.boot2 (vzx=0xbbd0bcbc) is 0x003c0000
Reading NAND CS0, addr 0x003c0000, size 0x00000800 to 0x01740000
Not a valid ROMFS
Skipping boot container 3.
Skipping boot container 4.
Skipping boot container 5.
Skipping boot container 6.
Skipping boot container 7.
Trying devtype=0 chipsel=1
nand_probe 0x0xd00f6ed0
Failed to init!
Trying devtype=2 chipsel=0
39idxfsef2f712148b75194ab1d3c691b55bd4d3a5e956dS

#xos2P4a-99 (sfla 128kbytes. subid 0xac/ac) [serial#52aa8ed10bc92da5e9e7de3cdeeabc9b]
#stepxmb 0xac
#DRAM setup (method=0x10015858) ...
#DRAM0 Window  :    0x#24#26#24#26# (18)
#DRAM1 Window  :    0x#2a#2c#26#28# (19)
#DRAM0 Settings: WD=0x0b0b0b0b RG=0x08090809 RR=0x08090809 RF=0x090a090a
#DRAM1 Settings: WD=0x0b0b0b0b RG=0x0a0a0909 RR=0x0a0a0909 RF=0x0a0b0a0a
#poisoned 131072 pages with 0xa7f2ce16
#step6 @0*** zxenv has been customized compared to build ***
--- review xmasboot/configs/922-A2.config for details [xmbb7-ezboot98-nand_st2] ---
xloadsize=59444
xload rc=6
subrom SHA-256: 43b5383fcd2ecd1f5366bea4eafc03bd740dc0a113af58d02846c117fb581b5b
ezboot98 @0xd00e5a94 (nand_st2) (actual cpu=@499MHz/dsp=333MHz/sys=333MHz)
on 8655 rev ES5 (subid 0xac) a2=0x00000002 a3=0x00000003
step12
#step22
ruamm0 [0x80000000,0x8f2f0000[ (~254738432 bytes)
ruamm1 [0xcca00000,0xcfd60000[ (~53870592 bytes)
[0xcfd20000,xos_public_ga=0xcfd20000[ and [0xcfd40000,0xcfd5ffff[ are lost for alignment)
x_ga=0xcfd1fcd4
[0x8e800000,ios_ga=0x8e800000[ and [0x8eeacfc1,0x8f2f0000[ are lost for alignment)
GW32 0x0006f008 0xc0000000 [va=0x84000000]
GW32 0x0006f00c 0xc4000000 [va=0x88000000]
GW32 0x0006f010 0xc8000000 [va=0x8c000000]
step33
xos2k client version=19, server version=19
xos2 SHA-1 = ef2f712148b75194ab1d3c691b55bd4d3a5e956d (version 0x4a)
xos2 serial = 52aa8ed10bc92da5e9e7de3cdeeabc9b
Using zbootxenv ga=0xcfd0bcbc (va=0xbbd0bcbc)

**************************************
* SMP86xx zboot start ...
* Version: 3.1.0
* Started at 0xd00ed770.
* Configurations (chip revision: 1):
*    Enabled checkpoints.
**************************************
DRAM0 dunit_cfg/delay0_ctrl (0x3514001a/0x4565132b).
DRAM1 dunit_cfg/delay0_ctrl (0x3514001a/0x4565132b).
Using UART port 0 as console.
Board ID.: villa_d2
Setting up H/W from XENV block at 0xbbd0bcbc.
  Setting <SYSCLK avclk_mux> to 0x17400000.
  Setting <SYSCLK hostclk_mux> to 0x00000130.
  Setting <IRQ rise edge trigger lo> to 0xff28ca00.
  Setting <IRQ fall edge trigger lo> to 0x0000c000.
  Setting <IRQ rise edge trigger hi> to 0x0c10009f.
  Setting <IRQ fall edge trigger hi> to 0x00000000.
  Setting <IRQ GPIO map> to 0x000a0800.
  Setting <PB default timing> to 0x03080202.
  Keeping <PB timing0> to 0x03080202.
  Keeping <PB Use timing0> to 0x000003f3.
  Keeping <PB CS Config> to 0x00330003.
  Enabled Devices: 0x001b3efc
    PCIHost Ethernet Ethernet1 IR FIP I2CM I2CS USB PCIDev1 PCIDev2 PCIDev3 PCIDev4 SATA SCARD SCARD1
  PCI IRQ routing:
    IDSEL 1: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
    IDSEL 2: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
    IDSEL 3: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
    IDSEL 4: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
  Smartcard pin assignments:
    OFF pin = 2
    5V pin = 0
    CMD pin = 1
  Smartcard1 pin assignments:
    OFF pin = 2
    5V pin = 0
    CMD pin = 1
cd#0 disabled
cd#1 disabled
cd#2 want 96000000Hz: setting of 0x0000000021c00000-2^28
cd#2 cannot measure
cd#3 disabled
cd#4 want 33333333Hz: setting of 0x0000000061333343-2^28
cd#4 measured to 33336kHz
cd#5 disabled
cd#6 disabled
cd#7 disabled
cd#8 disabled
cd#9 disabled
cd#10 disabled
cd#11 disabled
  GPIO dir/data = 0x00000880/0x00000880
  UART0 GPIO mode/dir/data = 0x6e/0x00/0x00
  UART1 GPIO mode/dir/data = 0x6e/0x04/0x04
  UART2 GPIO mode/dir/data = 0x00/0x00/0x00
  Generate pulse(s) with GPIO7 .. 1,0(16us),1
  MAC0: 00:90:a9:74:96:6a
  MAC1: 00:16:e8:e7:de:3c
XENV block processing completed.
Default boot index: 1, sel:1
Boot Index (2)
xmboot booted from devtype: 0, chipsel: 0, phyblocknum: 0
Explicit boot order specified:
  0x00 : devtype=0, CS=0
  0x01 : devtype=0, CS=1
  0x20 : devtype=2, CS=0
  0x21 : devtype=2, CS=1
WARNING: ezboot encroaches upon ruamm#0 zone
ezboot buffers, setup in DRAM bank#0:
  Alloting 1048576 bytes for heap.
  Alloting 8388608 bytes for reading.
  Alloting 8388608 bytes for decryption.
xmat romfs goes to 0xcfc0bca0 (ga)
xmat romfs goes to 0xb3c0bca0 (va)
Trying devtype=0 chipsel=0
nand_probe 0x0xd00f6ed0
nand_Mg_open 0
Reading NAND CS0, addr 0x016c0000, size 0x00000800 to 0xb3c0bca0
Not a valid ROMFS
Trying devtype=0 chipsel=1
nand_probe 0x0xd00f6ed0
Failed to init!
Failed to find valid xmat romfs in any device / chip select!
freeing xmat romfs buffer at 0xcfc0bca0
xmat romfs process failed.
Trying devtype=0 chipsel=0
reading z.boot2 (vzx=0xbbd0bcbc) is 0x003c0000
Reading NAND CS0, addr 0x003c0000, size 0x00000800 to 0x01740000
Not a valid ROMFS
Skipping boot container 3.
Skipping boot container 4.
Skipping boot container 5.
Skipping boot container 6.
Skipping boot container 7.
Trying devtype=0 chipsel=1
nand_probe 0x0xd00f6ed0
Failed to init!
Trying devtype=2 chipsel=0
39idxfsef2f712148b75194ab1d3c691b55bd4d3a5e956dS

#xos2P4a-99 (sfla 128kbytes. subid 0xac/ac) [serial#52aa8ed10bc92da5e9e7de3cdeeabc9b]
#stepxm
       b 0xac
#DRAM setup (method=0x10015858) ...
#DRAM0 Window  :    0x#24#26#24#26# (18)
#DRAM1 Window  :    0x#2a#2c#26#28# (19)
#DRAM0 Settings: WD=0x0b0b0b0b RG=0x08090809 RR=0x08090809 RF=0x090a090a
#DRAM1 Settings: WD=0x0b0b0b0b RG=0x0a0a0909 RR=0x0a0a0909 RF=0x0a0b0a0a
#poisoned 131072 pages with 0x0d75f738
#step6 @0*** zxenv has been customized compared to build ***
--- review xmasboot/configs/922-A2.config for details [xmbb7-ezboot98-nand_st2] ---
xloadsize=59444
xload rc=6
subrom SHA-256: 43b5383fcd2ecd1f5366bea4eafc03bd740dc0a113af58d02846c117fb581b5b
ezboot98 @0xd00e5a94 (nand_st2) (actual cpu=@499MHz/dsp=333MHz/sys=333MHz)
on 8655 rev ES5 (subid 0xac) a2=0x00000002 a3=0x00000003
step12
#step22
ruamm0 [0x80000000,0x8f2f0000[ (~254738432 bytes)
ruamm1 [0xcca00000,0xcfd60000[ (~53870592 bytes)
[0xcfd20000,xos_public_ga=0xcfd20000[ and [0xcfd40000,0xcfd5ffff[ are lost for alignment)
channel#ei
x_ga=0xcfd1fcd4
[0x8e800000,ios_ga=0x8e800000[ and [0x8eeacfc1,0x8f2f0000[ are lost for alignment)
GW32 0x0006f008 0xc0000000 [va=0x84000000]
GW32 0x0006f00c 0xc4000000 [va=0x88000000]
GW32 0x0006f010 0xc8000000 [va=0x8c000000]
step33
xos2k client version=19, server version=19
xos2 SHA-1 = ef2f712148b75194ab1d3c691b55bd4d3a5e956d (version 0x4a)
xos2 serial = 52aa8ed10bc92da5e9e7de3cdeeabc9b
Using zbootxenv ga=0xcfd0bcbc (va=0xbbd0bcbc)

**************************************
* SMP86xx zboot start ...
* Version: 3.1.0
* Started at 0xd00ed770.
* Configurations (chip revision: 1):
*    Enabled checkpoints.
**************************************
DRAM0 dunit_cfg/delay0_ctrl (0x3514001a/0x4565132b).
DRAM1 dunit_cfg/delay0_ctrl (0x3514001a/0x4565132b).
Using UART port 0 as console.
Board ID.: villa_d2
Setting up H/W from XENV block at 0xbbd0bcbc.
  Setting <SYSCLK avclk_mux> to 0x17400000.
  Setting <SYSCLK hostclk_mux> to 0x00000130.
  Setting <IRQ rise edge trigger lo> to 0xff28ca00.
  Setting <IRQ fall edge trigger lo> to 0x0000c000.
  Setting <IRQ rise edge trigger hi> to 0x0c10009f.
  Setting <IRQ fall edge trigger hi> to 0x00000000.
  Setting <IRQ GPIO map> to 0x000a0800.
  Setting <PB default timing> to 0x03080202.
  Keeping <PB timing0> to 0x03080202.
  Keeping <PB Use timing0> to 0x000003f3.
  Keeping <PB CS Config> to 0x00330003.
  Enabled Devices: 0x001b3efc
    PCIHost Ethernet Ethernet1 IR FIP I2CM I2CS USB PCIDev1 PCIDev2 PCIDev3 PCIDev4 SATA SCARD SCARD1
  PCI IRQ routing:
    IDSEL 1: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
    IDSEL 2: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
    IDSEL 3: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
    IDSEL 4: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
  Smartcard pin assignments:
    OFF pin = 2
    5V pin = 0
    CMD pin = 1
  Smartcard1 pin assignments:
    OFF pin = 2
    5V pin = 0
    CMD pin = 1
cd#0 disabled
cd#1 disabled
cd#2 want 96000000Hz: setting of 0x0000000021c00000-2^28
cd#2 cannot measure
cd#3 disabled
cd#4 want 33333333Hz: setting of 0x0000000061333343-2^28
cd#4 measured to 33344kHz
cd#5 disabled
cd#6 disabled
cd#7 disabled
cd#8 disabled
cd#9 disabled
cd#10 disabled
cd#11 disabled
  GPIO dir/data = 0x00000880/0x00000880
  UART0 GPIO mode/dir/data = 0x6e/0x00/0x00
  UART1 GPIO mode/dir/data = 0x6e/0x04/0x04
  UART2 GPIO mode/dir/data = 0x00/0x00/0x00
  Generate pulse(s) with GPIO7 .. 1,0(16us),1
  MAC0: 00:90:a9:74:96:6a
  MAC1: 00:16:e8:e7:de:3c
XENV block processing completed.
Default boot index: 1, sel:1
Boot Index (0)
xmboot booted from devtype: 0, chipsel: 0, phyblocknum: 0
Explicit boot order specified:
  0x00 : devtype=0, CS=0
  0x01 : devtype=0, CS=1
  0x20 : devtype=2, CS=0
  0x21 : devtype=2, CS=1
WARNING: ezboot encroaches upon ruamm#0 zone
ezboot buffers, setup in DRAM bank#0:
  Alloting 1048576 bytes for heap.
  Alloting 8388608 bytes for reading.
  Alloting 8388608 bytes for decryption.
xmat romfs goes to 0xcfc0bca0 (ga)
xmat romfs goes to 0xb3c0bca0 (va)
Trying devtype=0 chipsel=0
nand_probe 0x0xd00f6ed0
nand_Mg_open 0
Reading NAND CS0, addr 0x016c0000, size 0x00000800 to 0xb3c0bca0
Not a valid ROMFS
Trying devtype=0 chipsel=1
nand_probe 0x0xd00f6ed0
Failed to init!
Failed to find valid xmat romfs in any device / chip select!
freeing xmat romfs buffer at 0xcfc0bca0
xmat romfs process failed.
Trying devtype=0 chipsel=0
reading z.boot0 (vzx=0xbbd0bcbc) is 0x00080000
Reading NAND CS0, addr 0x00080000, size 0x00000800 to 0x01740000
Not a valid ROMFS
reading z.boot1 (vzx=0xbbd0bcbc) is 0x000c0000
Reading NAND CS0, addr 0x000c0000, size 0x00000800 to 0x01740000
Not a valid ROMFS
reading z.boot2 (vzx=0xbbd0bcbc) is 0x003c0000
Reading NAND CS0, addr 0x003c0000, size 0x00000800 to 0x01740000
Not a valid ROMFS
Skipping boot container 3.
Skipping boot container 4.
Skipping boot container 5.
Skipping boot container 6.
Skipping boot container 7.
Trying devtype=0 chipsel=1
nand_probe 0x0xd00f6ed0
Failed to init!
Trying devtype=2 chipsel=0


Hello I sent the log that putty restitusce I just connect the WDTV boot. Has anyone solved the problem? "Not a valid romfs"
thanks
funi
n00b
 
Posts: 3
Joined: Fri Jun 06, 2014 9:51 am

Re: WD TV LIVE power loss during update - BRICKED   

Postby recliq » Tue Jun 17, 2014 2:17 am

http://wiki.wdlxtv.com/Brick READ WITH CARE! TRY THE YAMON OPTIONS FIRST! (Pressing 0,1 or 2 during boot on serial console.)
­WDLXTV Project Maintainer
-:] If you like my contributions feel free to donate for a beer or a new flash drive. ...and always remember: RTFM! (README, FAQ, WIKI) [:-
User avatar
recliq
WDLXTV Team
 
Posts: 5513
Joined: Thu Apr 15, 2010 8:09 am
Location: Kiel, Germany


Return to WDTV Live

Who is online

Users browsing this forum: No registered users and 1 guest